MakerFocus 4pcs 3.7V Lithium Rechargeable Battery JST1.25 Connector 2pin, 952540 3.7V 1000mAh Battery with Protection Board and Insulated Rubber Tape Compatible with ESP32 Development Board
$28.38
Taxes will be calculated at Checkout.
US Delivery Time: 3-5 Business Days.
US Delivery Time: 3-5 Business Days.
Product Description
MakerFocus 4pcs 3.7V Lithium Rechargeable Battery JST1.25 Connector 2pin, 952540 3.7V 1000mAh Battery with Protection Board and Insulated Rubber Tape Compatible with ESP32 Development Board
4pcs 37V Lithium Rechargeable Battery, 852540 37V 1000mAh Battery with Protection Board and Insulated Rubber Tape Matched with ESP32 Development Board WiFi Kits for Ar duino NodeMcU Note: 1 The maximum operating current of this battery is only about 1A, can not be used for unmanned aerial vehicles, model aircraft or power tools and other products that require high current 2 This battery interface is JST 125 pitch male, it can be matched with some ESP32 Development Board that it come with Female JST 125 mm connectors Specification: Standard Voltage: 37V Rated capacity: 1000mAh Weight: About 17g Size: 85*25*40(mm) Working current: 15A Overcurrent protection: 23A Overcharge limit pressure: 425A005V Over-voltage limit pressure: 245A030V charge current time: Standard charging: 02c (8 hours) Fast charging: 05c (25 hours) The maximum charging current: 05c continuous Dishcarge current: 05c The maximum discharge current: 1c End-off voltage: 275Vpcs Allowable charging temperature: 0 +45 Allowable discharge temperature: -10 +60 Allowable storage temperature: -10 +40 ( within 3 months) -10 +30 ( within 6 months) Standard charging Method: charging this battery to 425V at 02c constant current, then charge the battery at a constant voltage of 42V till its charging current= 005c Package Including: 4 * 1000mAh 852540 37V Lithium Rechargeable BatteryFeatures of MakerFocus 4pcs 3.7V Lithium Rechargeable Battery JST1.25 Connector 2pin, 952540 3.7V 1000mAh Battery with Protection Board and Insulated Rubber Tape Compatible with ESP32 Development Board
Note: The battery overcurrent protection is not a panacea, do not continue to charge and discharge the current and voltage with a large current beyond the range, otherwise the protection board will be damaged and invalid 1000mAh: The recommended charging current is 02A, the maximum is not more than 1A The discharge current is recommended 055A, and the maximum is not more than 3A Over-discharge protection: When the battery is about to run out and the voltage is as low as 30V, the protection board will also be turned off and can no longer be discharged, forming an over-discharge protection effect Overcharge protection: When charging the battery, when the voltage reaches the highest battery voltage (42V), the protection board will automatically power off and shut down, indicating that it will not continue to charge when fully charged, form an overcharge protection Short circuit protection: When an accidental short circuit occurs, the protection board will automatically shut down within a few milliseconds and will not be powered on again Note that the cell is short-circuited (not through the protection board) The protection board will also fail due to continuous high current, or the components are heated and damagedSpecification of MakerFocus 4pcs 3.7V Lithium Rechargeable Battery JST1.25 Connector 2pin, 952540 3.7V 1000mAh Battery with Protection Board and Insulated Rubber Tape Compatible with ESP32 Development Board
| Product Details | |
|---|---|
| Color | Silver |
| Dimensions | 1.78X0.99X0.4 |
| Weight | 0.04 |
Warning - California Proposition 65 This product may contain chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.